General
115 results found
-
In the signal status display, explicitly show omitted phases
The Signal status window will show the phase has zero program time for the omitted phases but there are no other indicators for it being an omitted phase and stays red.
Customer has asked for enhancement so it doesn’t show the last known actual green time and instead shows omitted.3 votes
Econolite
responded
We are waiting for more customers to respond to this issue before moving forward.
-
9 votes
This is under review by development. We will update the status as soon as possible.
-
Be able to upgrade firmware remotely
Upgrade controller OS/App firmware from Centracs to field controller. We can schedule to upgrade firmware at midnight so it won't discrupt traffic during daytime. If we have 200-300 intersections, it save tons of time and money spent.
30 votes -
Add a label to the Vehicle Call (Square) in the map editior
There is no way to show what vehicle detector number is being called in the map editor. We have to overlay a label number to each detector for us to see what detector number is being called
5 votes -
Add ability to full screen content
All some content to be full screen the containers, such as the map and CCTVs.
1 voteEconolite
responded
We are waiting for more customers to respond to this issue before moving forward.
-
Add the ability to set a max to the amount of same alerts sent from centracs.
We are currently set up to receive email and text when a signal goes into flash and comes out of flash. One of the problems we have with that is sometimes a signal will go in and out of flash multiple times. Every time that happens we receive a notification. recently 2 of our signals had similar but slightly different problems. Signals 1 had a BIU issue that made the controller think the signal was going in and out of flash every 1 to 6 seconds even though the signal was not actually flashing. Which resulted in 461 notifications, which…
5 votes -
2 votesEconolite
responded
We are waiting for more customers to respond to this issue before moving forward.
-
Alert Trigger Editor - Fault Flash ON - Event Trigger Type should be in seconds, not minutes.
Currently, when using the Alerts and Events editor, the "Fault Flash - ON" Entry only allows for the event to trigger either once, X times in Y minutes, or active for Z minutes.
It would be preferred if we could set the third option in seconds, as waiting 1 full minute to get the alert is too long, but receiving the alert immediately runs the risk of receiving alerts for false alarms.
14 votesEconolite is reviewing the feasibility of such a task. An update will be posted when new information is available.
-
Be able to Import/Export Cobalt CFG files just like you can with ASC3 Data Base Files
I’m trying to import a file into Centracs that I grabbed from a Cobalt via a USB memory stick.
Centracs Version 2.1.3.21. Cobalt Version 32.65.30.
When I do the import I can only choose a .DB file even though you can see on the left (Entity Configuration) the entity is setup for a Cobalt.
I can actually rename the file as ASC3.DB and it will allow me up import and all of the data appears to be correct. I store in Centracs and close the editor. Then with I open the editor back up and try to export the data,…
3 votesThis is planned for the 2.2.2 Centracs Release. Please see your support engineer about the scheduled date for this release.
-
1 vote
-
Change "Bad" to "Poor"
Alerts and events logged typically have an adjective to denote the quality of an aspect of the system. For example, when communication decreases, an alert may display as "Communication Bad". Would it be possible to change this to "Communication Poor?" This should also apply to other alerts--"Bad" should be "Poor."
2 votesEconolite
responded
We are waiting for more customers to respond to this issue before moving forward.
-
Export Detector Data Export Format
Export detector data in a different format. Preferably one that can be read directly into Synchro. Recommended format would label the columns with the Intersection Name or Description (user decides), detector ID, date, and Time and the rows would contain all recorded data. The table should look as follows:
Date Time INID Detector1 Detector2 Detector37/13/2018 0845 1st & A St 14 125 62
7/13/2018 0900 1st & A St 12 145 486 votesEconolite is reviewing the feasibility of such a task. An update will be posted when new information is available.
-
1 voteEconolite
responded
We are waiting for more customers to respond to this issue before moving forward.
-
Allow exception / holiday days to be used in the scheduler as the active days.
Instead of having a scheduled event NOT run during exception/holiday days, I need the scheduled event to run on those days. Since users can group multiple days in the Exception/Holiday days event, it would be useful to be able to create and activate events during the holidays. Example: If a user creates an exception event for all fixed holidays during the year, it would be useful to be able to use that exception event for calling special patterns for those days with one scheduled event, instead of programming one for each holiday.
3 votesEconolite
responded
We are waiting for more customers to respond to this issue before moving forward.
-
Savable Print Templates
When printing make all the check box selections savable to a template. This would allow an user to selct that print template when printing timing sheets and not have to go through all the selections every time. EX: I could make a "3 timing plan, 8 phase, no overlap" template and use that when printing normal 8-phase quad intersections.
2 votesEconolite
responded
We are waiting for more customers to respond to this issue before moving forward.
-
When using search bar in the entity tree, populate the query as you type and not wait until the entire string is entered
When using the search function, it would be nice to have results show up when you enter in portions of the name of the intersection you are searching for. Some of the intersections we have rather long names.
2 votesThis issue is planned for the 2.2.2 release. Please see your support engineer about the scheduled date of the release.
-
Centracs MMS Icon editor
Centracs MMS does have an extensive list of Icons, however the list is severely lacking when moving beyond the traffic world. For this product to be stand alone or City wide it needs to be all encompassing. Adding the ability to add custom icons and then categorize them for various City departments would be an exceptional step forward.
5 votesEconolite
responded
We are waiting for more customers to respond to this issue before moving forward.
-
color code the split text or split field in the Split Monitor Report when the actual split meets or exceeds the programmed split.
In the Split Monitor Report's split table, it would be nice if the split text or cell would stand out when the actual split meets or exceeds the programmed split.
9 votesEconolite is reviewing the feasibility of such a task. An update will be posted when new information is available.
-
4 votesEconolite
responded
We are waiting for more customers to respond to this issue before moving forward.
-
color code the interesections that have failed communication in the Communication Statistics Report
similar to the way the Hourly Communication Statistics report is formatted.
2 votesEconolite
responded
We are waiting for more customers to respond to this issue before moving forward.
- Don't see your idea?